Quick Answer: Most standing desk repairs start and end with a reset: clear the floor, run the desk to its lowest height, hold the down button until the display shows RST (it looks like “ASr”) or RESET, then hold it again until the desk dips and rises. UPLIFT says 70% of the control boxes returned to it for replacement were not defective and would have been fixed by that reset. If a code comes back, look it up for your brand, because the same code means different things: E01 is a 2-minute duty-cycle cutoff on a FlexiSpot E7 and an overcurrent fault on an UPLIFT V3. When a part really has failed, UPLIFT sells a control box for $129 and a leg for $180; FlexiSpot, Herman Miller (Jarvis), Branch and Desky don’t sell those parts online, so for their desks the warranty claim is the parts store.
An electric standing desk has only four parts that can stop it moving: the power cord, the handset (keypad), the control box under the desktop and the legs, each of which holds a motor and spindle. The handset tells you which one it suspects, but in a code that is specific to the control box inside your desk. We compared the error-code tables, reset procedures, parts prices and warranty terms that FlexiSpot, UPLIFT, Autonomous, Branch, Desky and Herman Miller (Jarvis) publish in their own manuals, help centers and stores, checked on November 6, 2026. This guide covers error codes and resets; for a desk that grinds, strains or crawls without showing a code, start with our standing desk motor replacement guide, and for a desk that moves fine but sways, see our standing desk wobble guide.
Standing desk repair by the numbers
- 70% of the standing desk control boxes returned to UPLIFT for replacement “are not defective and would have been fixed by performing the Quick Desk Reset,” according to UPLIFT’s reset page.
- 2 minutes on, 18 minutes off: the 10% motor duty cycle printed by FlexiSpot (E7), UPLIFT (V2 and V3), Herman Miller (Jarvis) and Desky. Exceed it and the desk locks itself with an overheat code.
- 4 different meanings for E01 across the six code tables we compared: a duty-cycle or overuse cutoff (FlexiSpot E7/E8, Autonomous general keypad), overcurrent (UPLIFT V3), supply voltage too high (Autonomous Desk 5) and a firmware or connectivity fault (UPLIFT V2, Desky Dual).
- 1.5 inches: the height difference between legs after a reset at which UPLIFT asks you to call support instead of resetting again.
- $129 and $180: UPLIFT’s prices for a replacement control box and a replacement leg with motor, against $469 for a new UPLIFT V3 2-leg frame (upliftdesk.com, November 6, 2026).
- 1 electric standing desk recall in the CPSC recall database since 2018: about 19,000 Realspace Magellan desks in 2019, for a control box with reverse polarity.
Step 1: the reset that clears most codes
Every maker in this guide tells you to do the same thing first. The button names and timings differ slightly, but the sequence is the same:
- Clear the space under the desk. The desk will drive to its lowest height, and anti-collision can abort a reset if it touches a chair or cabinet.
- Check the cables. Power cord into the control box and the wall, handset cable and each leg cable pushed fully home. Desky’s manual lists these three connections before any other step, and Jarvis’s reset guide starts with unplugging and reseating every cable, including both ends of the leg cables.
- Lower the desk all the way and keep holding down. After about 10 seconds the display changes to RST (which reads “ASr” on a 7-segment display), RESET or a dash. Release.
- Hold down again until the desk dips slightly, rises slightly and stops. That bounce is the control box re-zeroing the legs. The reset is done when the height number comes back.
- If the down button does nothing, unplug the desk, wait, plug it back in and start again at step 3.
| Brand (handset) | Reset, per the maker | Display during reset | Unplug time if stuck |
|---|---|---|---|
| FlexiSpot E7 / E7 Pro | Hold â–Ľ to the lowest height, keep holding until the desk dips, rises and stops | ASr | 30 s (help article), at least 10 s (manual) |
| UPLIFT V3 / V2 | Hold down 10 s until ASr or RESET, release, hold down until it lowers slightly, rises slightly and stops | ASr (display keypads), RESET (Advanced Paddle) | V2: unplug and hold down for 30 s |
| Jarvis (Herman Miller) | Hold â–Ľ up to 15 s, release and repeat up to three times, then hold until the desk dips and pops back up | RESET (OLED), RST (older display) | Unplug all cables, reconnect, power last |
| Autonomous Desk 5 / Pro | Depends on the control-box part number on its label; Desk 5 (TC15s-H119): hold up and down together until the desk lowers and beeps | ---- or RST | 60 s unplugged, then 60 s plugged in |
| Branch Duo | Hold the paddle down 5 s until RESET appears, release, hold again until the height numbers return | RESET | Not specified |
| Desky Dual | Hold DOWN to the lowest height, hold DOWN 10 s until RESET, hold again until it lowers and slightly rises | RESET | Not specified; reset after any power cut |
Two details catch people out. First, a power cut or unplugging usually triggers the reset prompt: Desky’s manual says a manual reset “may be necessary” after a power outage, surge or unplugged cord, and the Autonomous Desk 5 and 5 Pro manuals say to reset after a power outage. RST on the display after a storm is a request, not a fault. Second, FlexiSpot warns that you must wait the full 30 seconds unplugged: “If you plug it into early your desk reset will not be successful.”
Same code, different fault: E01, E07 and H01 compared
There is no industry code standard. Each code table belongs to a specific control box, and makers change boxes between models: Autonomous alone lists six reset procedures by control-box part number. A code you look up for the wrong brand can send you to the wrong part. Even Eureka Ergonomic, which publishes a generic code table on its blog, calls it “a heuristic (rule of thumb)” and tells readers to check their own manual.
| Code | FlexiSpot E7 / E8 | UPLIFT V3 | Autonomous (general keypad) | Autonomous Desk 5 | Branch Duo | Desky Dual |
|---|---|---|---|---|---|---|
| E01 | Control box ran over 2 minutes continuously; rest 18 min | Overcurrent | Overuse protection, up to 20 min | Main power supply voltage too high | Not listed | Firmware/connectivity (E01-E13) |
| E02 | Motor overheated | Overcurrent | Unbalance protection | Spindle heights differ by more than 1 cm | Not listed | Firmware/connectivity |
| E03 / E04 | Motor overcurrent from overloading | Overcurrent | E03 anti-collision; E04 "T-touch protection" (check the control box is screwed down firmly) | E04 handset not connected | Not listed | Firmware/connectivity |
| E07 / E08 | Motor problem | Uneven or disconnected legs | Not listed | E07 supply voltage too low; E08 unbalance | 7 / 8: a leg gets no signal from the control box | Firmware/connectivity |
| E09 | Legs uneven | Uneven or disconnected legs | Not listed | Not listed | Not listed | Firmware/connectivity |
| E11-E13 | Not listed | Uneven or disconnected legs (E07-E12) | Motor M1, M2 or M3 overcurrent | M1 motor, sampling channel or phase cable not connected | 11 / 12 / 13: run a reset | Firmware/connectivity |
| H01 / HOT | Not listed | H01 overheated (duty cycle) | Not listed | HOT: overuse, power off 18 min | H01 overheat, clears in a few minutes | H01 'HOT' overheating, cool 20 min |
| RST / ASr | Reset state | Reset mode | Not listed | Reset reminder | RESET | RESET |
Sources: FlexiSpot’s “Error Code Troubleshooting for E7 or E8” help article and E7 manual, UPLIFT’s V3 manual (page 15), Autonomous’s error-code help page and Desk 5 manual, Branch’s Duo Standing Desk manual (v1.0, February 2025) and Desky’s Dual Sit Stand Desk instructions (2026, US). “Not listed” means the maker does not define that code in the source we used.
UPLIFT’s older V2 desks and Advanced Paddle keypad word it differently from the V3: E01-E06 are “firmware or connectivity issues” there (check the cables, then reset), and E07-E12 mean the legs are uneven. Herman Miller does not currently publish an error-code table for Jarvis desks, only the reset guide above.
Symptom to part: what actually failed
When a reset doesn’t stick, the symptom narrows it to one of four parts. This table pairs each symptom with the makers’ first fix and the part to replace only if that fix fails.
| Symptom | Usual cause | First fix | Part if the fix fails |
|---|---|---|---|
| Dark display, no response at all | No power | Try another outlet, reseat the power cord at both ends; Autonomous control boxes show a green light when powered | Power cord, then control box |
| Stops after several moves, H01 / HOT / FlexiSpot E01-E02 | 10% duty cycle used up | Leave it plugged in and wait 18-20 minutes | None |
| Slow, stalls under load, FlexiSpot E03-E04 or _OL | Over the lift rating | Remove weight: E7 355 lb, E7 Pro 440 lb, UPLIFT V3 355 lb, Desky Dual 308 lb | None |
| One side lower, FlexiSpot E09, UPLIFT E07-E12 | Legs out of sync, loose leg cable | Reseat leg cables, even out the load, full reset | Leg, if the gap stays over 1.5 in (UPLIFT) |
| Motor code (FlexiSpot E07/E08/E20-E23, Autonomous E11-E13) | Leg motor or control box | Reset, then the plug-swap test below | The leg if the code follows it, the control box if not |
| Desk reverses or stops for no reason | Anti-collision too sensitive, or a loose control box | Tighten the control box screws; lower the sensitivity setting | Control box |
| Display works, buttons do nothing, or it shows LOC | Keypad locked (not a fault) or failed handset | UPLIFT: hold M to unlock; check the handset cable | Handset |
| Memory presets land at the wrong height | Lost calibration | Full reset; FlexiSpot E7: hold M and the sitting-figure button 3 s to restore factory settings | None |
Anti-collision is adjustable on most current handsets. FlexiSpot’s E7 cycles through A-3 (high) to A-0 (off) when you hold ▲ and ▼ together for 5 seconds. UPLIFT sets it from the reset screen as 10.5 (most sensitive, “possible false positives”), 10.6 or 10.7 (least sensitive). Desky publishes the actual force: about 22 lb on High, 33 lb on Medium and 44 lb on Low. Branch’s Duo manual says a desk that lowers itself is “the desk’s auto collision feature being activated” and tells owners to make sure the control box “is tightly attached so that it does not shake or vibrate” before suspecting the motor.
The plug-swap test: leg or control box?
When a motor code survives a reset, FlexiSpot and Autonomous describe the same test, and it is the cheapest diagnostic in desk repair:
- Unplug the desk from the wall.
- At the control box, swap the left and right leg cables (on Autonomous desks, the M1 and M2 ports).
- Plug the desk back in, reset and watch the code.
If the code moves with the leg (an M1 fault becomes an M2 fault, or FlexiSpot’s code changes), that leg’s motor has failed and the leg needs replacing. If the code stays the same, FlexiSpot says “there is an error in the control program of the control box,” and Autonomous says the same about a fault that stays with one port: replace the control box. FlexiSpot lists a leg or control box that hit the floor during assembly as a likely cause of motor codes, because the knock can disconnect or damage internal wiring.
Don’t go further than swapping plugs. Herman Miller’s Jarvis manual says opening the lifting columns, control box or handset “risks electric shock and voids any warranty claims,” and Jarvis’s reset guide warns that a missing or wrong leg cable “can cause irreparable damage to your desk.”
What replacement parts cost
UPLIFT was the only maker of the six that listed motor parts with prices in its own US store on November 6, 2026. The others either don’t sell them online or sell them only through support.
| UPLIFT part | Fits, per UPLIFT | Price |
|---|---|---|
| Control box | UPLIFT V1, V2 and V2-Commercial desks | $129 |
| Replacement leg (FRM058), motor and spindle included | UPLIFT V2 and V2-Commercial | $180 |
| Basic Display Angled Keypad (FRM072) | All sit-to-stand UPLIFT desks | $29 |
| Advanced Comfort Angled Keypad (FRM066) | Any electric UPLIFT desk | $39 |
| Advanced Paddle Keypad (FRM055B) | Any height-adjustable UPLIFT desk | $69 |
| Replacement power cord | UPLIFT standing desks | $25 |
| Connecting cable | Short or long | $24 |
| For comparison: new V3 2-leg frame (FRMA-2) | Complete frame | $469 |
The repair-or-replace math on UPLIFT’s prices: a control box is 27% of a new V3 frame, a leg 38%, and a control box plus one leg ($309) 66%. Past that point a new frame, with a new warranty, is the better buy. One catch: UPLIFT lists the control box and leg for V1 and V2 desks only. We found no V3 control box or leg for sale, so V3 owners get those parts through a warranty claim.
The other makers, as of November 6, 2026:
- FlexiSpot sells no control boxes, handsets or legs in its US store. Its warranty says FlexiSpot “will replace (at no charge to you) the defective parts,” shipped free within the continental US.
- Herman Miller (Jarvis) lists only a $8 Jarvis caster among its replacement parts; control boxes, handsets and legs go through Herman Miller support.
- Branch and Desky sell no motor parts in their online stores. Branch’s warranty says “we’ll provide the parts needed to get your furniture back in working condition.”
- Autonomous says replacement parts are “sold separately” to the original purchaser, but its warranty does not cover those part orders and they are non-returnable. It publishes no parts price list.
The practical upshot: for every brand except UPLIFT, the warranty claim is the parts store, so check your term before you search for a generic control box. Third-party control boxes rarely match the leg connectors and firmware of a specific frame, which is also why makers like Branch void the warranty if “original parts are swapped out or third-party products are used.”
Warranty first: what each maker covers
| Maker | Motors and electrical parts | The fine print |
|---|---|---|
| UPLIFT | 15 years on nearly every product (orders since April 14, 2021); V3 Essential and V3 QuadZen 5 years | Free shipping both ways on approved claims only in year one; term shortened proportionally above 40 hours of use a week |
| FlexiSpot | E7 series 15 years, E5 10 years, all other height-adjustable desks 5 years (bought since April 1, 2022) | Defective parts replaced at no charge; original purchaser and authorized sellers only |
| Herman Miller (Jarvis) | 7 years on frame, mechanical parts, motors and electrical components | 5 years on tops, 1 year on power grommets and surge protectors |
| Branch | Standing Desk 10 years (bought after January 1, 2023; 3 years before), Duo and Four Leg 10 years | Open-box desks 5 years; void if bought on a marketplace |
| Autonomous | Desk 2 family 10 years, Desk Pro and Thinking Desk lifetime, Desk 5 Core 2 years | Desks bought from dealers or resellers are not covered; labor costs are not covered |
| Desky | Eco Single frame 3 years, per its product page | Check the product page for your frame |
Older desks are often still covered. UPLIFT’s warranty page lists 10 years for orders between July 22, 2020 and April 13, 2021, and 7 years including motors, control box and keypad for orders from March 10, 2015 to July 21, 2020. Fully’s own 2023 Jarvis reset guide still described “a 15-year warranty on all frame and electrical parts”, so if your Jarvis was bought from Fully, keep the original order confirmation. Our brand guides to UPLIFT, FlexiSpot, Jarvis, Branch and Autonomous desks cover each warranty in more detail.
Recalls: one electric desk since 2018
A search of the CPSC recall database turns up one electric standing desk recall since 2018: the Office Depot Realspace Magellan Performance Electric Height-Adjustable Desk (recall 19-759, July 10, 2019), about 19,000 desks sold from April 2017 to February 2019 (SKUs 358370 and 216230). The control box had “an electrical issue resulting in reverse polarity, which could pose a shock hazard,” and the remedy was a free replacement control box. If you own one and never received the new box, stop using the desk and contact Office Depot. Two 2019 recalls covered desktop converters rather than electric desks: about 76,000 Knape & Vogt gas-spring sit-stand workstations and about 22,700 Humanscale QuickStand Lite units.
When to stop and call the maker
- A motor or leg code survives a reset and the plug-swap test.
- The legs still differ by more than 1.5 inches after a reset (UPLIFT’s threshold), or a Jarvis desk turns lopsided at any point, which Herman Miller says is the moment to stop troubleshooting.
- The desk smells hot or trips the breaker, or the control box is damaged.
- The desk is under warranty. Autonomous, for example, asks for the error code and a brief description of the problem, and a covered part costs nothing.
If repair isn’t worth it, our best standing desk frame guide compares replacement frames you can bolt your existing top onto, and our best standing desk roundup covers complete desks. A sinking office chair is a similar parts-first fix; see our office chair repair guide.
The bottom line
Reset before you buy anything: a full reset clears most codes, and UPLIFT’s own return data says 7 in 10 “failed” control boxes weren’t failed at all. Read codes against your own brand’s table, because E01 alone means four different things across the desks in this guide. Use the plug-swap test to tell a bad leg from a bad control box, and check the warranty before ordering parts: for FlexiSpot, Jarvis, Branch and Desky the part comes from support, and for UPLIFT owners outside the warranty a $129 control box or $180 leg is still a fraction of a $469 new frame.
Sources
Checked on the makers’ websites and CPSC’s recall database on November 6, 2026: FlexiSpot “Error Code Troubleshooting for E7 or E8” (help center at flexispot.com/support), FlexiSpot E7 manual, FlexiSpot E7 Pro manual, FlexiSpot warranty; UPLIFT reset and troubleshooting, UPLIFT desk programming, UPLIFT V3 manual, UPLIFT V2 manual, UPLIFT replacement parts, UPLIFT 2-leg frame, UPLIFT warranty; Autonomous error codes, Autonomous reset guide, Autonomous Desk 5 manual, Autonomous warranty policy; Branch Duo Standing Desk manual, Branch warranty; Desky Dual Sit Stand Desk instructions (US, 2026); Jarvis reset guide (Herman Miller), Jarvis assembly instructions, Jarvis Laminate Standing Desk (warranty); Eureka Ergonomic reset article; CPSC Realspace Magellan recall. We could not load Vari’s support pages when we checked, so Vari desks are not in the code tables.